Whether you’re prepping your Commander for some off-road action or simply performing routine maintenance, at some point you’re going to need to remove the radiator. This job is not difficult, but there are a few things you need to know before you get started. In this article, we’ll walk you through the process of removing the radiator from your Can-Am Commander, step by step.
First, disconnect the negative battery terminal to prevent any electrical shorts. Next, remove the front grill and plastic shrouding. There are several 10mm bolts holding these pieces in place. With the grill and shrouding removed, you will have better access to the radiator. There are two hoses connected to the radiator, as well as the overflow tank. Disconnect these hoses and unscrew the radiator from its mounts. Be careful when removing the radiator, as it is delicate and can be easily damaged.
How do you remove a radiator?
There are several stages to removing a radiator. First, you have to turn the heating off and wait until the pipes are cool to the touch. Next, you have to isolate the radiator and drain it down. Finally, you can unscrew it from the wall, take it outside and continue with your project.
If you need to replace your radiator, it’s a pretty straightforward job that can be done in a couple of hours. The easiest way to do it is to replace your radiator with one that is the exact same size as your old one. This way, you won’t have to make any adjustments to your existing setup.
How do you replace a radiator
If your car is overheating, or if the radiator isn’t working properly, you may need to change the radiator. Here’s how:
1. Locate the Coolant Drain/Petcock and Drain Coolant
2. Remove Radiator Fan and Fan Shroud
3. Remove Radiator
4. Inspect and Replace Thermostat
5. Reinstall Radiator and Fan Shroud
6. Reconnect coolant hoses, refill, and bleed.
Removing a radiator is a fairly simple process that can be completed with just a few basic tools. An adjustable spanner, a radiator bleed key, and a bucket are the only essential pieces of equipment. If you want to remove the wall brackets after removing the radiator, you’ll also need a suitable screwdriver.
What tool do I need to remove a radiator?
To safely remove your radiator from the wall, you will need the following tools:
An adjustable spanner
A pair of grips
2 towels
To remove the radiator, first turn off the heating and allow the radiator to cool. Once it is cool, use the adjustable spanner to loosen the bolts that hold the radiator to the wall. Once the bolts are loose, use the grips to carefully remove the radiator from the wall. Be careful not to damage the wall or the radiator. Place the radiator on the towels to protect it from scratches.
If you’re experienced with replacing radiators, it shouldn’t take more than a couple of hours. However, if you’re new to the task, it could take up to eight hours to complete. Make sure you have all the necessary parts before beginning the job.
Can removing a radiator cause problems?
If you have removed your radiator and there are now problems, it is likely that the system has been incorrectly fitted. This is a complicated issue and cannot be resolved by DIY plumbing. You will need to call a central heating specialist (plumber).
If you need to remove a radiator from your home, you don’t necessarily need to drain the entire system. Here’s how to do it:
1. Close the radiator valves.
2. Shut down the lockshield and the TRV, which are on the opposite sides of the radiator.
3. Drain the radiator.
4. Pull the valve off.
5. Remove the radiator from its brackets.
6. Tilt the side of the radiator.
7. Refit the radiator after painting.
Is moving a radiator easy
Moving an electric radiator is usually a far simpler job than moving a central heating radiator. Most electric radiators are just plugged into a power socket, meaning that they can be taken off the wall and fixed to the new wall before being plugged into another socket. This makes them much easier to move around than central heating radiators, which are often fixed in place.
If your radiator is not properly functioning, the heat from your engine will not be able to escape. This can cause your car to overheat. If this happens, the excess heat can severely damage components in your vehicle. This can end up costing a considerable amount of money to repair.
What parts are needed to replace radiator?
Before removing the old radiator, most vehicles will need to have the following parts disconnected: the reservoir hose, the upper and lower radiator hoses, the cooling fan electrical connector, the cooling fan, the transmission cooler lines, and the mounting bolts.
To turn off your heating, follow these steps: turn off the valves, drain the radiator, open the bleed valve, loosen the other valve, and disconnect the radiator. Lift it off the brackets and you’re done!
Are radiators reverse threaded
A cast iron radiator has normal thread on one side and reverse (left-hand) thread on the other. This allows for the radiator to be installed in either a vertical or horizontal position.
Isolating and draining a particular radiator is a much simpler task than draining the entire system. To prepare, simply place a container over a towel underneath the valve of the radiator you’ll be working on. Then, undo the nut joining the radiator and the valve.
Can I use a screwdriver instead of a radiator key?
A slotted bleed screw is a convenient way to bleed a radiator without using a bleed key. Just insert a screwdriver into the slot and turn it in a counter-clockwise direction to bleed the radiator.
If you need to move your cast iron radiator, follow this guide to do so safely. First, unwrap the radiator and lift it into a vertical position, ensuring that you lift from the centre and not at one end. Next, carry the radiator maintaining its vertical position. Finally, set the radiator down on its feet in the new location.
Conclusion
1. Remove the front grill by unscrewing the bolts that hold it in place.
2. Unscrew the bolts that hold the radiator in place.
3. Pull the radiator out and set it aside.
The removal of the radiator from a Can Am Commander is not a difficult task and can be completed in a short amount of time. With a few tools and careful planning, the process can be completed quickly and easily.
